Abstract: The probe (20) includes a conductivity sensor (38) and an optical sensor (39) for detecting the depth of a layer of oil, gasoline, etc floating on the surface of water in a well. A battery (60) is included in the probe, and a resistor (R1) is provided in series with the conductivity sensor. When the probe is in oil, both sensors are OFF, and no voltage is detectable at the surface; when the probe is in air, the optical sensor is ON and the conductivity sensor is OFF, so that a maximum voltage is detectable at the surface; and when the probe is in water, the optical sensor is OFF and the conductivity sensor (with its resistor) is ON, so that an intermediate voltage, as set by the value of the resistor, is detectable at the surface.

Abstract: The packer (4) is for use in isolating long lengths (i.e. heights) of a borehole (2), e.g. between sampling points. The packer includes bentonite (23) which is activated by the natural groundwater in the borehole. The water is admitted into the bentonite through narrow portholes (21), which delays the flow of water into the packer. The water is distributed evenly throughout the bentonite by blotting paper (14,16) which soaks up the incoming water and prevents the water passing to the bentonite until the blotting paper is all saturated. Alternatives to the use of blotting paper, to transmit the water evenly over and through the whole body of bentonite, include perforated corrugated plastic, corrugated cardboard, and perforated plastic pipes.

Abstract: The packing-seal is shown in use in a borehole as a level-isolating seal for a groundwater sampler. The packing-seal shown includes an expandable annulus of Dowell (TM) water-expandable material. Surrounding that is a pressure-sleeve of rubber. A sheet of woven Kevlar (TM) is wrapped circumferentially around the sleeve and the Dowell annulus, such that the ends of the Kevlar sheet overlap. Outside the Kevlar is an outer rubber sleeve. Upon expansion of the packing seal to fill the borehole, the Kevlar sheet unwraps to allow the Dowell to expand without restraint. Once the packing seal has filled the borehole, the Kevlar sheet is prevented from unwrapping further. If the borehole contains a fissure the Kevlar provides a rigid bridge over the fissure, and prevents the packing-seal from ballooning out into the fissure.

Abstract: One electrode of the probe is its tubular outer sleeve (3), and the other is its central rod (4). The insulators (9,16) separating the two are attached rigidly to the central rod, whereby the outer sleeve may slide off the probe for cleaning and servicing purposes. The outer sleeve is held in place simply by friction from the O-ring seals (12,30). When the sleeve is removed, the central rod, insulators, etc., remain as a structurally complete sub-assembly. Electrical contact with the outer sleeve is made through an expandable canted coil spring (20), mounted on an insulator. The central rod is formed with a massive center section (7), for weighting the probe. The probe is supported on a graduated tape (36), in which are embedded the electrical leads (38) to the probe. The leads are securely attached and sealed in place by means of heat-shrinkable material (50), which is wrapped around the leads, heat-shrunk, and compressed into a pocket (27).

Abstract: A probe is disclosed, for lowering into a water-well or other hole. The probe includes conductivity measuring electrodes, to distinguish between e.g., water and contaminants, such as gasoline. The probe also includes an optical sensing facility to locate the junction between air and liquid. The probe comprises a transparent plastic tube, mounted inside a housing. A beam of light from a LED passes obliquely through the plastic tube and onto a photo-transistor. When liquid is encountered in the well, the liquid enters the tube: the change in refractive index now directs the beam away from the photo-transistor. The optical and conductivity sensors are both actuated at the same depth.

Abstract: The sampler includes a cylinder, plugged at the lower end, the plug having a first one-way check valve to permit the sample to flow upwards into the chamber. A piston is slidable in the bore, and includes a second one-way check valve, which permits the sample to flow upwards through the piston. In use, the sampler is pressurized from above, in order to hold both valves closed, and lowered to the correct depth; the pressure is released, and the sample flushes through the chamber of the sampler. The sampler is then re-pressurized, and drawn to the surface, with the sample remaining totally contained and maintained at depth-pressure. The sample may be transferred out of the chamber for analysis, by pressurizing the piston, without the sample losing its depth-pressure status.

Abstract: In use, the probe (1) is dropped into a ground-hole (3), for the purpose of detecting the depth of the steel casing (16) of the hole. The probe comprises a long, slim, tubular housing (2) made of stainless steel. Attached inside the housing is a springy stalk (10) made of PVC. The stalk is deflectable laterally, and carries a magnet (11) at its free end. The magnet responds to the steel, and causes the stalk to deflect while in the presence of the steel. The housing, and a stainless steel sleeve (12) around the magnet, comprise a pair of electrical contacts, which break apart and send a signal to the surface when the magnetic influence disappears. The probe is suspended on a cable (4) which is calibrated to indicate the depth of the probe when the signal is received.