Abstract: An unsynchronized acoustic or radio-frequency (RF) computed tomography (CT) imaging system with matched, but independent, continuous wave (CW) transmitters and receivers configured to radiate acoustic or RF transmissions in a plurality of vector paths through solid geologic material. A computer calculates and displays tomographic images constructed from individual acoustic or RF path signal travel time or attenuation measurements logged from registered locations from the CW transmitters and receivers after their being shuttled amongst a number of different transmitter and receiver perspectives available around said geologic material to generate data necessary for computed tomography. Each of the transmitters and receivers include independent unsynchronized crystal oscillators rated at 10-ppm or better frequency uncertainty to produce and to detect CW radio frequency (RF) transmissions.

Abstract: Acoustic heterodyne radars use accurately surveyed or otherwise known locations to repetitively launch at least two, intense acoustic tone soundwaves (F1, F2) into an underground area of search. An acoustic receiver is tuned to receive either the sum (F1+F2) or difference (|F1?F2|) heterodynes and is configured to measure and log the overall relative attenuation and roundtrip travel times of the soundwaves, like a typical radar. Any acoustic heterodynes received are assumed to be the work of non-linearities and stresses in the search area. A full-waveform three dimensional tomography algorithm is applied by a graphics processor to the collected and logged data to generate maps and profiles of objects beneath the ground which are interpreted to have produced the acoustic heterodynes.

Abstract: An underground tunnel detection system does not employ radar. Instead, an automatic frequency control is used to keep a continuous wave (CW) transmission tuned to the resonant frequency of a resonant microwave patch antenna (RMPA). Changes in loading and the bulk dielectric constant of the mixed media in front of the RMPA will affect its resonant frequency and input impedance. A significant shift in the measured input impedance is interpreted as a possible tunnel, and the phase angle of the measured input impedance tends to indicate a slightly forward or aft position relative to the detection system rolling over it on the ground surface.

Abstract: An unsynchronized acoustic or radio-frequency (RF) computed tomography (CT) imaging system with matched, but independent, continuous wave (CW) transmitters and receivers configured to radiate acoustic or RF transmissions in a plurality of vector paths through solid geologic material. A computer calculates and displays tomographic images constructed from individual acoustic or RF path signal travel time or attenuation measurements logged from registered locations from the CW transmitters and receivers after their being shuttled amongst a number of different transmitter and receiver perspectives available around said geologic material to generate data necessary for computed tomography. Each of the transmitters and receivers include independent unsynchronized crystal oscillators rated at 10-ppm or better frequency uncertainty to produce and to detect CW radio frequency (RF) transmissions.

Abstract: A movement detection system includes a microwave antenna able to transmit microwave frequency signals into a space. An electronics controller is connected to the microwave antenna, and is configured to continually measure the impedance of the microwave antenna while it transmits microwave frequency signals into the space. An interpretive device is connected to receive impedance measurements from the electronics controller, and is configured to interpret and report changes in the magnitude and phase angles of individual impedance measurements as the passing of things and their direction through the space.

Abstract: An underground tunnel detection system does not employ radar. Instead, an automatic frequency control is used to keep a continuous wave (CW) transmission tuned to the resonant frequency of a resonant microwave patch antenna (RMPA). Changes in loading and the bulk dielectric constant of the mixed media in front of the RMPA will affect its resonant frequency and input impedance. A significant shift in the measured input impedance is interpreted as a possible tunnel, and the phase angle of the measured input impedance tends to indicate a slightly forward or aft position relative to the detection system rolling over it on the ground surface.

Abstract: A beat-product radio imaging method (RIM) system uses a matched continuous wave (CW) transmitter and receiver to electronically image material in between. Signal attenuation measurements are taken from a number of different transmitter and receiver perspectives around the material. The transmitter and receiver each have a crystal oscillator rated at 10-ppm or better frequency uncertainty. The receiver's crystal oscillator is used as a local oscillator to beat down the transmitter's carrier frequency to baseband. The frequency error between the local oscillator and the transmitter carrier frequencies produces a beat product of less than one Hertz in frequency and its magnitude is inversely proportional to the path attenuation between the transmitter and receiver. An extremely low-pass filter is used to remove everything above one Hertz in the detector. The receiver sensitivity is therefore extraordinarily high.

Abstract: A movement detection system includes a microwave antenna able to transmit microwave frequency signals into a space. An electronics controller is connected to the microwave antenna, and is configured to continually measure the impedance of the microwave antenna while it transmits microwave frequency signals into the space. An interpretive device is connected to receive impedance measurements from the electronics controller, and is configured to interpret and report changes in the magnitude and phase angles of individual impedance measurements as the passing of things and their direction through the space.

Abstract: A beat-product radio imaging method (RIM) system uses a matched continuous wave (CW) transmitter and receiver to electronically image material in between. Signal attenuation measurements are taken from a number of different transmitter and receiver perspectives around the material. The transmitter and receiver each have a crystal oscillator rated at 10-ppm or better frequency uncertainty. The receiver's crystal oscillator is used as a local oscillator to beat down the transmitter's carrier frequency to baseband. The frequency error between the local oscillator and the transmitter carrier frequencies produces a beat product of less than one Hertz in frequency and its magnitude is inversely proportional to the path attenuation between the transmitter and receiver. An extremely low-pass filter is used to remove everything above one Hertz in the detector. The receiver sensitivity is therefore extraordinarily high.

Abstract: A system for detection of linear underground anomalies passing under surface roads comprises an electromagnetic (EM) gradiometer mounted on a vehicle trailer. A transmitter is mounted to the front bumper of a car or vehicle towing the trailer and provides carrier synchronization information to the EM-gradiometer. An opportunistic radio station can be used as an illuminator. The transmitter or ground wave from an opportunistic radio station directs radio waves down into the ground where objects like linear underground anomalies and their equipment will produce reflections and scattered waves. These reflections will have phase angles and magnitudes that can be interpreted for characterizing information about the linear underground anomalies. Each EM-gradiometer measurement is tagged with GPS location information and then stored in a database. Subsequent passes over the same roadways and tracks are compared (change detection) to the earlier stored data.

Abstract: An aerial electronic system for detection of surface and underground threats comprises an electromagnetic (EM) gradiometer flown aloft over the possible ground and underground threats to a convoy. The EM gradiometer is disposed in a Styrofoam torpedo shaped pod that is towed in flight behind an airplane. An illumination transmitter and loop antenna mounted to the airplane radiate a primary EM wave that travels down to the ground surface and penetrates beneath. Frequencies of 80 KHz to 1 MHz are selected according to whether the targets are laying on the surface or deeply buried. Detonation wire pairs, buried cables and pipes, and other conductors will re-radiate a secondary wave that can be sensed by the EM gradiometer. A reference sample of the transmitter signal is carried down a fiberoptic from the airplane to the towed pod. This signal is used in the synchronous detection to measure the secondary EM wave phase.

Abstract: A slickline data transmission system for a high pressure oil-field well comprises inductive couplers at opposite ends of a slickline in order to establish real-time radio communication between down-the-hole logging toolstrings and supervisory control and data acquisition equipment on the surface. A frequency shift keyed (FSK) carrier centered around radio is used to send data up to the surface and commands back down to the toolstring. The toolstring itself can be a conventional one with a TDMA interface originally intended to be memory-dumped when the toolstring is returned to the surface.